Organochlorine residues in two seal species from Western Iceland

Harbour seals and grey seals from Faxaflói (Western Iceland) were analyzed for contamination with organochlorines (HCB, PCBs, p,p′-DDT, p,p′-DDE, chlordanes and the enantiomers of α-HCH). Although the values strongly varied, both harbour seals and grey seals on average showed comparable levels of PCBs, p,p′-DDT, p,p′-DDE and α-HCH, as well as chlordanes (ΣCD). Differences were measured in the HCB content of the seal species. The HCB/α-HCH ratio in harbour seals was <1 and in grey seals >1. The results from seals on Iceland were compared with data derived from seal samples of the Antarctic, the Arctic (Spitzbergen) and the North Sea (Germany) in order to give an insight into the global distribution of pollution with chlorinated organics.     

Combined nitrification/denitrification in a membrane reactor

An ever stricter legislation regulating wastewater leads to an increasing demand for biological treatment plants which are able to selectively eliminate nitrogen from wastewaters with a high influent concentration, even when operating in partial influent mode. A membrane-tube-module (MSM) reactor (Membran-Schlauch-Modul-Reaktor) was constructed and realized in the IUV at the University of Bremen. The present approach makes use of all the various layers of the whole biofilm, enabling nitrification and denitrification processes to run simultaneously in one and the same biofilm under optimized conditions. The biological degradation capacity of the system was first successfully tested with synthetic wastewater, and subsequently in a real application with effluents from a recycling of animal carcasses plant and from a coke-oven plant. A mathematical model was devised which describes this biofilm system. The resulting equations were solved by means of the simulation software AQUASIM.     

Occurrence and behaviour of linear alkylbenzenesulphonates, nonylphenol, nonylphenol mono- and nonylphenol diethoxylates in sewage and sewage sludge treatment

The fluxes of linear alkylbenzenesulphonates (LAS), nonylphenol (NP), nonylphenol monoethoxylate (NP1EO) and nonylphenol diethoxylate (NP2EO) through sewage and sludge treatment of 29 Swiss sewage treatment plants were investigated. Reversed-phase high-performance liquid chromatography (HPLC) was used to determine LAS. Normal-phase HPLC was employed to measure NP, NP1EO and NP2EO which are metabolites of the nonionic surfactants of the nonylphenol polyethoxylate type (NPnEO). Quantitative determinations were performed of raw sewage, primary and secondary effluents and of sewage sludge. Under normal conditions of sewage and sludge treatment, LAS were efficiently removed from the raw wastewater (> 99% w/w) and were partly transferred to the sewage sludge (15–20% w/w). About 50% (molar base) of NPnEO in the sewage were transformed to NP and accumulated in the digested sludge. Large variations existed among different sewage treatment plants. It was estimated that 1.0 g m⁻² y⁻¹ of LAS and 0.3 g m⁻² y⁻¹ of NP are applied with sewage sludge to Swiss soils.     

An Experimental Determination of a Real Fire Performance of a Non-Load Bearing Glass Wall Assembly

A glass wall assembly was exposed to an intense real-scale compartment fire. The wall assembly consisted of four glass sections, two of which were fitted with tempered double-pane glass and the other two sections were fitted with tempered single-pane glass. At each glass section, temperatures were measured at the exposed face and the unexposed face. Total heat flux gauges were used to measure both the temporal variation of the energy incident on the glass wall and the transmitted energy rate detected through two of the glass sections. Visual and infrared cameras were used to image the unexposed face of each wall assembly during the fire exposure. Results of glass breakage and subsequent glass fall out were compared to studies in the literature for glass sections exposed to compartment fires. The behavior of the glass wall assembly under a fire load is presented.

Isotopenuntersuchungen zur Wechselwirkung von Grund- und Oberflächenwasser in der Entstehungsphase von Bergbauseen

Environmental isotopes such as ³ H, ² H, ¹⁸ O, ³⁴ S and ²²² Rn were applied to characterize relationships within and between ground and surface waters in two developing mining lakes. Using a two-component-model the portion of saline waters ascending through the lake bottom into the lakes was estimated. Similarly the contribution of pyritic sulphur participating in the lake sulfate has been assessed. Locally, the lakes are hydrochemically stratified. Mixing processes are reflected by all isotopes mentioned above. δ ¹³ C _DIC values of the most mineralized lake water did not correspond with those of deep groundwater from Zechstein strata revailing additional effects such as CO ₂ production. ²²² Rn was checked for assessing groundwater fluxes through the lake bottom. ²²² Rn was found in lake water regions with elevated salt contens but being always in an equilibrium with radium (excepting the sediment-lake water interface). Thus, radium must be taken in consideration in order to interprete radon values in saline groundwaters.     

Advanced controlling of anaerobic digestion by means of hierarchical neural networks

In this work several feed-forward back propagation neural networks (FFBP) were trained in order to model, and subsequently control, methane production in anaerobic digesters. To produce data for the training of the neural nets, four anaerobic continuous stirred tank reactors were operated in steady-state conditions at organic loading rates (Br) of about 2 kg m(-3) d(-1) chemical oxygen demand, and disturbed by pulse-like increase of the organic loading rate. For the pulses additional carbon sources like flour, sucrose, 1,2-diethylen glycol or vegetable oil were added to the basic feed, which consisted of surplus and primary sludge of a local waste-water treatment plant, to increase the chemical oxygen demand. Measured parameters were: gas composition, methane production rate, volatile fatty acid concentration, pH, redox potential, volatile suspended solids and chemical oxygen demand of feed and effluent. A hierarchical system of nets was developed and embedded in a decision support system to find out which is the best feeding profile for the next time steps in advance. A 3-3-1 FFBP simulated the pH with a regression coefficient of 0.82. A 9-3-3 FFBP simulated the volatile fatty acid concentration in the sludge with a regression coefficient of 0.86. And a 9-3-2 FFBP simulated the gas production and gas composition with a regression coefficient of 0.90 and 0.80, respectively. A lab-scale anaerobic continuous stirred tank reactor controlled by this tool was able to maintain a methane concentration of about 60% at a rather high gas production rate of between 5 and 5.6 m3 m(-3) d(-1).     

Laser pyrolyzed organosilazane-based Al/ZrO2 composite coating on stainless steel: Resulting microstructure and mechanical properties

Protective ceramic-based coatings are frequently the most suitable solutions for problems like corrosion and wear. It has been shown that the precursor technology is suitable for the preparation of ceramic coatings by pyrolysis in a furnace. However, the required high temperature for the preparation of the ceramic coatings limits this approach to high temperature-resistant substrates. A very innovative approach to overcome this restriction is the use of laser radiation as a thermal source for the pyrolysis of the preceramic polymer. In this paper, we report on a coating system, for steel substrates, consisting of a polysilazane (Durazane 2250) bond coat and a hard and dense top-coat composed of an organosilazane (Durazane 1800) with tetragonal ZrO₂ particles and aluminum flakes as fillers pyrolyzed using Nd:YVO₄ laser. The aluminum fillers led to a significant increase in absorption of the laser energy leading to the formation of a dense coating with a thickness up to 20 μm and a mainly cellular/columnar-dendritic microstructure. The microstructure, mechanical, and tribological behaviors of these composite coatings are reported and compared to those of laser pyrolyzed glass/ZrO₂-filled polysilazane-based coatings reported in the literature.     

Short fiber-reinforced oxide fiber composites

This paper presents a novel fiber spraying process for the manufacturing of short fiber bundle-reinforced Nextel™ 610/Al₂O₃-ZrO₂ oxide fiber composites (SF-OFC) and its characterization. First, the influence of varying fiber lengths (7, 14, and 28 mm, continuous fibers) and fiber orientations (unidirectional 0°, quasi-isotropic, ±45°) was investigated using hand-laid SF-OFC. Due to the weak matrix, the hand-laid material exhibited a strongly fiber-dominated material behavior, that is, variations in fiber length and orientation had a strong influence on the material properties. Second, the automated sprayed SF-OFC, however, exhibited a random orientation of the fiber bundles, which resulted in in-plane isotropic material properties. Average bending strengths of up to 177 MPa, strains of .39%, and a quasi-ductile fracture behavior were achieved. The strain was, therefore, in the range of fabric-reinforced OFC. While the bending strength of the SF-OFC was somewhat lower than that of fabric-reinforced OFC with the fiber orientation parallel to the loading direction, it was more than two times higher than the strength in 45° direction relative to the fabric reinforcement. Combined with good drapability and lower material costs compared to fabric-reinforced OFC, SF-OFC is, therefore, a promising material for industrial applications.     

Current Trends in Pretreatment and Fractionation of Lignocellulose as Reflected in Industrial Patent Activities

The pretreatment process to disintegrate lignocellulose and to fractionate its three main components hemicellulose, cellulose, and lignin, is a crucial step to enable sustainable and economic value chains based on biomass feedstock. This review provides an overview of the recent patenting activities on pretreatment. Most of these activities focus on optimization of different known processes to improve economics, such as increased catalyst efficiency, effluents recirculation, or lignin valorization. However, also a number of patents and demonstration activities based on emerging concepts for pretreatments are observed.     

Anatomical,Morphological, and Phytochemical Effects of Inoculation with Plant Growth- Promoting Rhizobacteria on Peppermint (<Emphasis Type="Italic">Mentha piperita</Emphasis>)

Plant growth-promoting rhizobacteria (PGPR) generally exert their effects through enhancement of plant nutrient status and/or phytohormone production. The effects of PGPR on aromatic plant species are poorly known. We measured plant growth parameters, chlorophyll content, trichome density, stomatal density, and levels of secondary metabolites in peppermint (Mentha piperita) seedlings inoculated with PGPR strains Bacillus subtilis GB03, Pseudomonas fluorescens WCS417r, P. putida SJ04, or a combination of WCS417r?+?SJ04. The treated plants, in comparison with controls, showed increases in shoot biomass, root biomass, leaf area, node number, trichome density, and stomatal density, and marked qualitative and quantitative changes in monoterpene content. Improved knowledge of the factors that control or affect biosynthesis of secondary metabolites and monoterpene accumulation will lead to strategies for improved cultivation and productivity of aromatic plants and other agricultural crops without the use of chemical fertilizers or pesticides.